6120C надпись "Nokia" и перезагруз

[Fluderator]

Продолжение выше изложенного лога:

СелфТест
Selftests to proceed: 31
Passed		ST_TAHVOINT_TEST
Passed		ST_UEM_CBUS_IF_TEST
Failed		ST_EAR_DATA_LOOP_TEST
Passed		ST_SIM_CLK_LOOP_TEST
Passed		ST_SIM_IO_CTRL_LOOP_TEST
Passed		ST_SECURITY_TEST
Passed		ST_PWR_KEY_TEST
Passed		ST_CURRENT_CONS_TEST
Passed		ST_BACKUP_BATT_TEST
Passed		ST_SLEEPCLK_FREQ_TEST
Passed		ST_HOOKINT_TEST
Passed		ST_BTEMP_TEST
Passed		ST_EXT_DEVICE_TEST
Passed		ST_CDSP_RF_BB_IF_TEST
Passed		ST_CDSP_RF_SUPPLY_TEST
Passed		ST_CDSP_TX_IQ_TEST
Passed		ST_CDSP_TXC_DATA_TEST
Passed		ST_CDSP_PWR_DETECTOR_BIAS_TEST
Passed		ST_CDSP_RX_PLL_PHASE_LOCK_TEST
Passed		ST_CDSP_TX_PLL_PHASE_LOCK_TEST



Запись РПЛ и НПС
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Simlock...
Handling as SL1/SL2 Simlock Data
Simlock NOT ACCEPTED !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
Restarting MCU...
Processing FBUS Part...
Writing Simlock...
Handling as SL1/SL2 Simlock Data
Simlock NOT ACCEPTED !
Processing FLASHBUS Part...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
CMT NPC Erased
CMT NPC Written
CMT HWC Erased
CMT HWC Written
CMT CCC Erased
CMT CCC Written
Restarting MCU...
Write RPL Finished!
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Processing 1730001978B901584A11D929C0CF1AE792AD304A_28.02.2013_110039.NPC.CMT.crt...
CMT NPC Erased
CMT NPC Written
Write CMT NPC Certificate finished
Restarting MCU...
All files processed OK!


RPL Calculation
BB5 Unlock Started...
MCU Version	V 07.10
MCU Date	15-07-09
Product		RM-243 (Nokia 6120 classic)
Manufacturer	(c) Nokia
IMEI		359808016439187
Mastercode	2523163761
Warning: Failed to read SP Info, Assuming defaults
Simlock Server	SIMLOCK SERVER
Simlock Key	0000000000000000
Simlock Profile	
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Reading Security Block...
Security block OK and saved to "RM-243_359808016439187_17.03.2013_132008.SecurityBlock.PM"
"1730001978B901584A11D929C0CF1AE792AD304A.C00045B2" Exists, That is good...
Checking for Rootkey Hash support with selected Unlock Method...
Selected Unlock Method: RPL Calculation
Asking box to calculate RPL...
Received RPL from Box OK!
Writing Simlock...
Simlock ACCEPTED OK !
MCU Version	V 07.10
MCU Date	15-07-09
Product		RM-243 (Nokia 6120 classic)
Manufacturer	(c) Nokia
IMEI		359808016439187
Mastercode	2523163761
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	8000000000000006
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Unlock finished! Time taken 3.391s


SX4_rep_SD
SX4 Authorization / SD Repair Procedure Started....
"1730001978B901584A11D929C0CF1AE792AD304A.C00045B2" Exists, That is good...
MCU Version	V 07.10
MCU Date	15-07-09
Product		RM-243 (Nokia 6120 classic)
Manufacturer	(c) Nokia
IMEI		359808016439187
Mastercode	2523163761
Reading Security Block...
Security block OK and saved to "RM-243_359808016439187_17.03.2013_132134.SecurityBlock.PM"
Superdongle Key is probably CORRUPTED, Writing custom keys...
Received SD Keys from box, writing to phone...
Superdongle Key ACCEPTED OK !
SX4 Status: Not authorized (76)
Started mutual authenthication with card...
Receiving Phone Seed 1...
Phone Seed 1 Received
Sending calculated Data 1, and expecting Seed 2...
Calculated Data 1 accepted, Phone Seed 2 Received
Sending calculated Data 2
Calculated Data 2 sent, Checking Authorization Status again
Authorization successfully finished!
Looking for Virgin PM In Database...
Found, writing...
[1,0] Written, Length: 114 bytes, Status: OK
[1,1] Written, Length: 4 bytes, Status: OK
[1,2] Written, Length: 98 bytes, Status: OK
[1,4] Written, Length: 110 bytes, Status: OK
[1,5] Written, Length: 4 bytes, Status: OK
[1,6] Written, Length: 98 bytes, Status: OK
[1,8] Written, Length: 110 bytes, Status: OK
[1,13] Written, Length: 98 bytes, Status: OK
[1,15] Written, Length: 4 bytes, Status: OK
[1,16] Written, Length: 98 bytes, Status: OK
[1,18] Written, Length: 98 bytes, Status: OK
[1,20] Written, Length: 98 bytes, Status: OK
[1,22] Written, Length: 16 bytes, Status: OK
[1,23] Written, Length: 4 bytes, Status: OK
[1,24] Written, Length: 84 bytes, Status: OK
[1,25] Written, Length: 4 bytes, Status: OK
[1,26] Written, Length: 110 bytes, Status: OK
[1,27] Written, Length: 4 bytes, Status: OK
[1,28] Written, Length: 98 bytes, Status: OK
[1,29] Written, Length: 10 bytes, Status: OK
[1,31] Written, Length: 98 bytes, Status: OK
[1,33] Written, Length: 36 bytes, Status: OK
[1,34] Written, Length: 80 bytes, Status: OK
[1,40] Written, Length: 16 bytes, Status: OK
[1,41] Written, Length: 182 bytes, Status: OK
[1,42] Written, Length: 4 bytes, Status: OK
[1,43] Written, Length: 36 bytes, Status: OK
[1,44] Written, Length: 182 bytes, Status: OK
[1,46] Written, Length: 64 bytes, Status: OK
[309,0] Written, Length: 4 bytes, Status: OK
[309,1] Written, Length: 2 bytes, Status: OK
[309,2] Written, Length: 12 bytes, Status: OK
[309,4] Written, Length: 12 bytes, Status: OK
[309,5] Written, Length: 12 bytes, Status: OK
[309,7] Written, Length: 12 bytes, Status: OK
[309,8] Written, Length: 12 bytes, Status: OK
[309,17] Written, Length: 12 bytes, Status: OK
Write PM Finished, Record written OK: 37, Record written NOT OK: 0


Analyse_Security
Started Phone Security Analysis...
MCU Version	V 07.10
MCU Date	15-07-09
Product		RM-243 (Nokia 6120 classic)
Manufacturer	(c) Nokia
IMEI		359808016439187
Mastercode	2523163761
Reading Security Block...
Security block OK and saved to "RM-243_359808016439187_17.03.2013_132323.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
-- SIMLOCK PROBLEM --

Phone have failed SIMLOCK Test, that means Simlock Area is DAMAGED!
To repair simlock area, Select Unlock method : "RPL CALCULATION",
And then click DIRECT UNLOCK. SL Area will be re-formatted.

-- SIMLOCK PROBLEM --
Step 2 : Testing SECURITY
SECURITY SEFLTEST PASSED OK!
Step 3 : Analyzing Security Block
"1730001978B901584A11D929C0CF1AE792AD304A.C00045B2" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
SIMLOCK FOUND AND CHECKSUM OK! PASSED!
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking ECC KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!

На данный момент аппарат ведет себя так-же,включается надпись "Nokia" и перезагруз.Все мои программные действия в логе.Думаю что ПМ пролился во все блоки при Sx4 или его отдельно надо записывать?

[KorAll]

Что бросилось в глаза при просмотре:

Сообщение от Fluderator

Phone have failed SIMLOCK Test, that means Simlock Area is DAMAGED!
To repair simlock area, Select Unlock method : "RPL CALCULATION",
And then click DIRECT UNLOCK. SL Area will be re-formatted.

Дословно - ТА имеет повреждённый SIMLOCK Test, что означает Simlock Area повреждена. Для ремонта выберите анлок метод:"RPL CALCULATION".
Затем клик DIRECT UNLOCK. Ты так делал или иначе? Если так не делал - то пробуй.

Сообщение от Fluderator

Checking CMLA KEYS...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)

Это наверно только ATF сделать может? Поэтому на будущее - 1, 120, 308 и 309 блоки PM сохраняй перед любым стиранием.

Удачи.

P.S.

Сообщение от Fluderator

Думаю что ПМ пролился во все блоки при Sx4 или его отдельно надо записывать?

При Sx4 ты записал 1 и 309 блоки, а главный гемор из-за 120 и 308 которых нет или разрушены! Поправте если я ошибаюсь.

[yurii-62]

Сообщение от Fluderator

На данный момент аппарат ведет себя так-же,включается надпись "Nokia" и перезагруз.Все мои программные действия в логе.Думаю что ПМ пролился во все блоки при Sx4 или его отдельно надо записывать?

Офф.Переводчик Google - Google Translate>> http://www.google.ru/search?client=o...hannel=suggest
Попробуйте пользоваться этим, для прочтения Ваших логов, 2 в разделах ATF, BEST, MXbox, Циклон есть даже видео инструкции по решению Вашего вопроса, думаю что при внимательном прочтении, и просмотре как это делать вопросы отпадут сами собой..

..........

Хотя если вдумчиво прочитать эту тему тут Все разжёвано, ток осталось собраться форумом приехать и сделать Вам эту несчастную NOKIA..

[yurii-62]

Fluderator

PS.

Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.

Обратите внимание на это, кабель необходим 7 пиновый или он дефектный.
2. В Циклоне вроде должен использоваться адаптер JAF/UFS? для кабеля.

Решение для "SECURITY_TEST failed!" и "warning: SD authorized but verify failed!"

После успешного ремонта SuperDongle и/или Simlock это происходит из-за отсутствия HWC и CCC полей. Из-за этого телефон находится в Contact Retailer или Contact Service даже если Simlock и SuperDongle в порядке.

Решение 1 (помогает не всегда, зависит от степени повреждения ПО телефона):

Запишите полный PM от телефона той же модели (с тем же product code) без полей 1, 308, 309 (и без поля 120 для SL20 телефонов)
Отключите / подключите телефон боксу !!!
Сделайте Simlock RPL repair
Сделайте SD RPL repair
Отключите / подключите телефон к боксу !!!
Сделайте SUPER SX4 Auth и затем запишите 1 и 309 поля PM

Если это не помогает, то используйте Решение 2:

Сделайте бэкап RPL (NPC, CCC, HWC, ...), назов*****1104;м его ORIGINAL RPL
Сделайте бэкап RPL из другого рабочего телефона (такой же модели) с таким же product code
Отредактируйте этот хороший RPL из другого телефона удалив NPC секцию (все линии которые начинаются с NPC_DATA_1 ... NPC_DATA_xx), будем называть этот отредактированный файл CLONE RPL

Сделайте бэкап PM из другого рабочего телефона (такой же модели) с таким же product code,
назов*****1104;м этот файл CLONE PM
Полностью сотрите флэш чип
Прошейте телефон (CMT, APE, ...)
Загрузите CLONE RPL
Загрузите ORIGINAL RPL
Запишите полный CLONE PM без 1,120,308,309 полей
Отключите / подключите телефон боксу !!!
Сделайте Simlock RPL repair
Сделайте SD RPL repair
Отключите / подключите телефон боксу !!!
Сделайте SUPER SX4 Auth и затем запишите 1 и 309 поля PM

Приложил что необходимо для этого, рабочие. Как это сделать циклоном думаю разберётесь..

[Fluderator]

Сообщение от yurii-62

В Циклоне вроде должен использоваться адаптер JAF/UFS? для кабеля.

Этот кабель я использую,желтый адаптер,без него Bb5 платформы не прошивает,а вот почему это ошибка выходит не пойму.Кабель разбирал,прозванивал все гуд.

[yurii-62]

Сообщение от Fluderator

Этот кабель я использую,желтый адаптер,без него Bb5 платформы не прошивает,а вот почему это ошибка выходит не пойму.Кабель разбирал,прозванивал все гуд.

Встречался с таким, все вроде в норме а не работает, может зависеть от качества самих проводов, береш другой все гуд, но вообще сейчас пользуюсь прищепками удобно, и с сопротивлением поиграть можно что не мало важно особенно с проблемными телами, советую...
ЗЫ. а по USB делать пробовал..? Проребболь все таки проц флеш, начни с флеш, может по ими какая бяка или отбито чо.