Обновления RIFFbox JTAG

[shoxa907]

17.03.2012

RIFF JTAG добавил поддержку восстановления загрузчика и реанимации модели Samsung GT-i9210 Galaxy S II LTE, обновил модули ПО QUALCOMM Partition Tool 1.06 и Galaxy Partition tool 1.04.


В этом обновлении RIFF Box:

Добавлена поддержка операций полного восстановления для моделей:
Samsung GT-i9210 Galaxy S II LTE
Обновлено ПО:
QUALCOMM Partition Tool v1.06
Galaxy Partition tool v1.04

Исправлена поддержка:
HTC Sensation (PG85130)
HTC Evo 3D (HTC Shooter)

Источник:
Подробнее: jtagbox.com

Для закачки и установки новых файлов, нажмите кнопку Check For Updates на вкладке Box Service в ПО.
Для удобной и легкой закачки ПО и flash-файлов RIFF воспользуйтесь torrent-треккером RIFF Box.

http://www.jtagbox.com/
http://www.riffbox.org/
Legija, Rocker team

[yurii-62]

21.03.2012
RIFF JTAG – HTC Sensation XL X315 / Bass (HTC Runnymede) Unbrick, Unlock, IMEI and CID update supported
Repairing bricked HTC SensationXL (PI39200) is easy using RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC SensationXL boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 1.25.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG3920000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC SensationXL:
Solder JTAG cable to HTC SensationXL JTAG pads;
Insert battery and connect USB Data cable;
Make sure HTC SensationXL is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
Источник.. http://www.jtagbox.com/jtag-news/rif...ed-world-first

[shoxa907]

25.03.2012

RIFF JTAG добавил поддержку восстановления загрузчика модели LG E510 Optimus Hub (LG Univa) и обновил библиотеку Samsung_I917.dll.


Добавлена поддержка операций восстановления для модели:
LG E510 Optimus Hub (LG Univa)

Исправлена поддержка:
Samsung I917
- добавлены данные восстановления для аппаратной ревизии 1.3

Источник:

Подробнее: http://www.jtagbox.com/

Для закачки и установки новых файлов, нажмите кнопку Check For Updates на вкладке Box Service в ПО.
Для удобной и легкой закачки ПО и flash-файлов RIFF воспользуйтесь torrent-треккером RIFF Box.

http://www.jtagbox.com/
http://www.riffbox.org/
Legija, Rocker team

[yurii-62]

27.03.2012

RIFF JTAG – Samsung SCH-I500 Galaxy S Mesmerize/Fascinate Unbrick Supported
Repairing bricked Samsung SCH-I500 Galaxy S Mesmerize/Fascinate is easy with RIFF Box.
I500 is based on the S5PCxxx Processor (ARM core is Cortex-A8). Please note the adaptive clocking mode (RTCK) is not available on this processor, so make sure to select a fixed TCK frequency.
To establish the JTAG connection attach battery cable and press Power On key.
In case after resurrection the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung I500:
Solder JTAG cable to Samsung I500 JTAG pads;
Attach battery cable and press Power On key;
Make sure Samsung I500 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
.

Статья:
http://www.jtagbox.com/jtag-news/rif...rick-supported

[yurii-62]

31.03.2012

RIFF JTAG – Samsung SCH-i920 Omnia II 8GB Unbrick – Dead Boot repair supported

Repairing bricked Samsung I920 AP (PDA Part) is easy with RIFF Box. Due to some hardware pecularities, we recommend to use only battery without USB cable connected. Please note, during connection establishment phase you will have to press the Power On key twice.
To resurrect Samsung I920 AP:
Solder JTAG cable to Samsung I920 AP JTAG pads;
Make sure Samsung I920 AP is selected in the list of models;
Insert battery; make sure no USB cable or charger is connected;
Press the Power On key;
Click Resurrect button;
When it stops at “Establish communication with the phone…” press the Power On key again;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
To resurrect Samsung I920 CP:
Solder JTAG cable to Samsung I920 CP JTAG pads;
Make sure Samsung I920 CP is selected in the list of models;
Insert battery and connect USB cable or charger;
Wait till AP part boots up completely;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
.

Источник:
http://www.jtagbox.com/jtag-news/rif...pair-supported