X1-01 не прошивается

[mizuk01]

Сообщение от SergeyT

Если после прошивки версии 07.51 залочится, лейте 05.39.

Что за бред?С какого это перепуга он залочится?

Connect phone on selected interface...

Read and Check phone data...
Infineon checking...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000048800
FLASH ID : UNKNOW [Not In Base]
Boot Done!


Done!

Connect phone on selected interface...

Core version : 1.35 Rev : 1.5

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm713_007.510
PPM : rm713_007.51ei
CNT : rm7130_nai07.51ei

Infineon flashing...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000048800
FLASH ID : UNKNOW [Not In Base]
Boot Done!

===Flashing [MCU]===
File : rm713_007.510
Image : hw_b1_rm713_r07.510.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00000000 , Len : 0x00020000
Erasing, wait ...
Erase done
Write , Start : 0x00000000 , Len : 0x00006000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00800000 , Len : 0x00400000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x003F0000
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00C5D000 , Len : 0x00203000
Erasing, wait ...
Erase done
Write , Start : 0x00C5D000 , Len : 0x0019E700
Flashing , wait ...
Region flash done
Check : 6AB2
===Flashing [PPM]===
File : rm713_007.51ei
Image : hw_b1_rm713_007.51ei.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00100000 , Len : 0x00700000
Erasing, wait ...
Erase done
Write , Start : 0x00100000 , Len : 0x0054B8C0
Flashing , wait ...
Region flash done
Check : 29E4
===Flashing [CNT]===
File : rm7130_nai07.51ei
Image : hw_b1_rm7130_nai07.51ei.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00E60000 , Len : 0x00100000
Erasing, wait ...
Erase done
Write , Start : 0x00E60000 , Len : 0x000B7F80
Flashing , wait ...
Region flash done
Check : AC31

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!


Init Service mode... Wait...

Afterflash settings...
SW ver : V 07.51
12-12-11
RM-713
(c) Nokia
IMEI : 3562690************68
PCode : 059D833
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
All done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
SW ver : V 07.51 12-12-11 RM-713 (c) Nokia
IMEI : 3562690************68
PPM : V 07.51
12-12-11
RM-713
(c) Nokia
EI
PCode : 059D833
BPCode : 059C3M4
HWID : 3051
LCDVer : WIN:BARACOAv80
NT39121
IMEI : 3562690************68
Sl Conf : 001-01-00000000000
Sl Prof : 000000000003000-2
Sl Aux : 000B0000
Hw Sig : E9E94C3B468FCF5C
Provider : Default Test Operator

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

Done!