Как можно калибровать сенсор с помощю Инфинити

[Rootcat]

ща покажу лог
ксинтел
open comport:COM7
please turnon your phone ,until connect success(press F4 Abort).
connecting mobile phone.
CPU Model:6225
downloading bootloader files ...
downloading bootloader files ...
bootloader files version:03.01
booloader operation in NOR Flash.
Flash type:[Fujitsu] MB84VP24491HK, MB84VP24591HK
flash ID:0004227E (22212200) [7]
flash size:01000000 (16.0M)
Ext RAM size:00400000 Int RAM Size:0000C000
>>Read flash information done.

лог инфина
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6225:8A03:8A00]...
CPU: MT6225
high speed boot enabled
chip: 0001:8103:0004
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
460800
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw1: KCM25_GEMINI_PCB01_GPRS_MT6225_S00.MAUI_GEMINI_W08 _12.BIN
ver. sw2: MAUI.GEMINI.W08.12, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 04227E22212200:18E59F00000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
.......................
detect standard fat location pass #1...
.................................................. ..
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #1 detected ok
detecting ffs structure pass 2...
.......................
detect standard fat location pass #1...
.................................................. ..
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
ffs element #2 detected ok
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Finished, time used: 73 sec
Remove/Install battery now

пробуем все три способа калибровки

Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: N801_for_V01b_20080705
Version: KCM25_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35336800015464
connection Ok
detecting structure #5 (mode-1)...
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19error:
detection failed (20 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 94 sec
Remove/Install battery now !
просит не снимая батарею включить и выкл тел.не получается его выключить ибо тело висит на вкл экране.
такие вот дела

[maslovets]

Сообщение от Rootcat

error:
detection failed (20 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 94 sec
Remove/Install battery now !
просит не снимая батарею включить и выкл тел.не получается его выключить ибо тело висит на вкл экране.
такие вот дела

Он просит:
1. Забекапиться.
2. Выполнить "format ffs"
3. Включить телефон.
4. Выключить телефон с кнопки не вытаскивая АКБ.
5. Провести калибровку повторно. Если не поможет, вычитать фул и отослать на суппорт с пометкой "touchscreen calibration failed".

Другими словами необходимо повторить калибровку на чистом ЕЕПРОМе.

По поводу реальности автокалибровки: работает, проверял сам. Разумеется, если строение фула известно софту и он может найти калибровочные переменные.