Поиск решения Ruggear RG 510 loko не включается

[motokmips]

Есть в наличии два телефона Ruggear RG 510 loko , один рабочий с него считывал прошивку и Full (но прошивка в нём RG500 ?), во второй прошивка и Full пишется без ошибок, но не включается логи прилагаю.
========================= Start

========================= 
                 24.08.2017 / 17:40:15
========================================================= 
Card found : v0136
Chinese Miracle II  [MTK module] v 1.58

Load File 
File_Info   : simcom72_wet_jb3
FileVersion : MT6572
Load File Ok

Start  at : [24.08.2017 / 17:41:06]
Operation : Flash [ v1.58 ]

======= Flash
Files set for flashing : 
[ MCU ] : MT6572__RUGGEAR__RG500__RG500_Russian_20_V2.0_V6W_20141029__Android_4.2.2.ispff

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D3034473A53E88DC191B5
Initialize Memory ... 
DRAM configured from IDB!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G40ME
[eMMC] : FLASH_CID : 45010053454D3034473A53E88DC191B5
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID    : 0x48409EF717AFF13E29AF16DDF215251F
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


USBDL : Init HSUSB Ok!
Brand     : ruggear
ProdName  : RG500
ProdModel : RG500
Device    : RG500
AndroidVer: 4.2.2
MTKxCPU   : MT6572
MTKxPRJ   : RG500_Russian_20_V2.0_V6W_20141029

ISPFF  ID : 6572 , TARGET ID : 6572

Flash pre-erase enabled
Erase Flash now ...
Flash pre-erase done

Write Flash now ...
[ MCU ] : MT6572__RUGGEAR__RG500__RG500_Russian_20_V2.0_V6W_20141029__Android_4.2.2.ispff

Init Ok , Sending blocks ... 
Write done , 3776 blocks sent

Done!
Elapsed: 00:05:28
Reconnect Power/Cable!

Finish at : [24.08.2017 / 17:46:33]

Start  at : [24.08.2017 / 17:46:50]
Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D3034473A53E88DC191B5
Initialize Memory ... 
DRAM configured from IDB!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G40ME
[eMMC] : FLASH_CID : 45010053454D3034473A53E88DC191B5
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID    : 0x48409EF717AFF13E29AF16DDF215251F
INT RAM    : 0x00020000
EXT RAM    : 0x20000000 [512 MiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done Erased/damaged phone?

Done!
Elapsed: 00:00:22
Reconnect Power/Cable!

Finish at : [24.08.2017 / 17:47:12]

[sever20067]

Сверить Preloader оттуда где сливали прошивку и маркировку флеши на который заливаете.

[motokmips]

Два идентичных аппарата, один работает, а второй не включается, потребление ~50mA

[sever20067]

Если дело не в прошивке, значит дело в железе.
И я ещё раз напишу, сверьте, ибо Вы не предоставили нормально информации, а гадать на кофейной гуще удел совсем других людей и они тут не сидят.

[motokmips]

Память в Read-Only