Chinese Miracle II [SPD module] v 1.00

[yurii-62]

CPU ID : 6531
Check/Read Info.

Chinese Miracle II  [SPD module] v 1.00

Start  at : [17.10.2014 / 14:13:48]
Operation : Check/Read Info [ v1.00 ]

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 48 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Done!

Elapsed: 00:01:27

Reconnect Power/Cable!

Read FullFlash..

Chinese Miracle II  [SPD module] v 1.00

Start  at : [17.10.2014 / 14:17:00]
Operation : Read FullFlash [ v1.00 ]

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 48 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Saved to : C:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD25LQ32.bin
Done!

Flash..

Finish at : [17.10.2014 / 14:25:26]

FastCheck : SPD65xx
Load file...
Not found any ExtInfo data (Compressed already)
Load Ok


Start  at : [17.10.2014 / 14:26:45]
Operation : Flash [ v1.00 ]

======= Flash
Files set for flashing : 
[ MCU ] : SPD6531_00400000_GD25LQ32.bin

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 48 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000

======= Flashing MCU
Mapping file ... 
Mapping done
Processing file : SPD6531_00400000_GD25LQ32.bin
Init ok, send data
Flashing Done!

Info : In some cases after flash required make "Format Fs / Reset Phone"

Done!


Elapsed: 00:01:28

Reconnect Power/Cable!

Read NV.

Start  at : [17.10.2014 / 14:34:52]
Operation : Read NV [ v1.00 ]

1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery

 ====  Wait for phone...

Phone found! [ 48 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ... 
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data ... 
Reading NV ... 
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\6531_NV_00008000.nv

Elapsed: 00:00:27

Reconnect Power/Cable!

ТА. после прошивки работает, все ОК.. (небольшое неудобство заметил, иногда приложение зависает, останавливать получалось только через диспетчер устройств, на ОС. ХР-пак3..
Repair Security не успел сделать, клиент торопыга...