Nokia 5130 белый экран и отключается

[Fluderator]

Здравствуйте уважаемые коллеги и товарищи!У меня следующая проблема с телефоном nokia 5130 XM.Пришел на ремонт с диагнозом белеет экран и выключается,аппарат включается нормально,но потом через 10-20секунд работы белеет дисплей и вырубается.Прошил его версией 9,97 с UFS не помогло,потом прошил с Циклоном тойже версией не помогает.SelfTest все "Passed" сбросы проходит нормально,но иногда сбросы с первого раза не проходят приходится чекать и заново сбрасывать.Ничего не помогало решил порлностью стереть телефон и понизить версию до 9,95,стирал телефон с Циклоном забекавив RPL,потом все по порядку заливал и восстанавливал так же с Cyclone box.Ситуация не изменилась и при повторной прошивке с Уфсом.Вот логи Cyclone box:

Инфо:

MCU Version	V 07.95
MCU Date	03-02-10
Product		RM-495 (Nokia 5130 XpressMusic)
Manufacturer	(c) Nokia            
IMEI		352700045099842
Mastercode	3236654057
IMEI Spare	3A25070054908904
IMEI SV		3325070054908944F8000000
PPM		V 07.95, 03-02-10, RM-495, (c) Nokia            , EL
CNT		Content: el_blu, V 07.95, 03-02-10, RM-495, (c) Nokia            , 
PSN		0AD60A3AI
Product Code	0572174
Module Code	0204024
Basic Product Code	0567772
PSD		0000000000000000
LPSN		0
RETU		16
TAHVO		22
AHNE		30
HW		2003
RFIC		06540601
DSP		ICPR72_10w01
LCD		SEIKO
BT		2222-302
Simlock Server	SIMLOCK SERVER
Simlock Key	2440700000000000
Simlock Profile	0000000000000000
Simlock Key Cnt	0
Simlock FBUS Cnt	0
Simlock [1,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [1,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [1,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [1,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [2,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [2,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [2,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [3,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [3,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [3,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [4,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [4,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [4,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [5,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [5,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [5,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [6,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [6,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [6,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,1]	State: OPENED	Type: MCC-MNC	Data: FFFFFF
Simlock [7,2]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,3]	State: OPENED	Type: GID	Data: FFFF
Simlock [7,4]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Simlock [7,5]	State: OPENED	Type: IMSI	Data: FFFFFFFFFFFFFFFF
Auto Selecting Flash Files on User Request...
Product Code: 0572174
This is Valid BB5 Product
No variant found with given Product Code, selecting first one

Прошивка:
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-495_352700045099842_30.11.2012_171102.SecurityBlock.PM"
WARNING: "192002117FD34950B8A59709FED7C8CD1762B1CE.C00045B2" Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.30.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
Exploiting - running preloader...
Preloader running OK, Running Custom Loader...
Custom loader running OK! Working...
Old Loader Detected
Readed OK, Saving to "192002117FD34950B8A59709FED7C8CD1762B1CE.C00045B2"
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
CMLA Key Store Problem -> Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
CMT PARTNERC Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Backing up simlock...
MCU Version	V 07.95
MCU Date	03-02-10
Product		RM-495 (Nokia 5130 XpressMusic)
Manufacturer	(c) Nokia            
IMEI		352700045099842
Mastercode	3236654057
Simlock backup OK, saved to RM-495_352700045099842_30.11.2012_171121.SLBackup.PM
Backup simlock thread finished, continuing...
Pre flash tasks finished, continuing...
Processing rm495__07.95.mcusw (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
rm495__07.95.mcusw, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x000006BF, NOR
EraseArea[0,CMT]: 0x000006C0-0x0001FFFF, NOR
EraseArea[0,CMT]: 0x00040000-0x000BFFFF, NOR
EraseArea[0,CMT]: 0x000C0000-0x0013FFFF, NOR
EraseArea[0,CMT]: 0x00140000-0x0137FFFF, NOR
EraseArea[0,CMT]: 0x01380000-0x0151FFFF, NOR
Waiting 320s for erasure finish...
Erase taken 73.860s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT NOLO Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT UPDAPP Certificate...
Writing CMT DSP0 Certificate...
Writing CMT MCUSW Certificate...
Programming Status OK!
All blocks written OK! Time taken 64.969s
Flashing Speed: 2349,53 kBit/S
Restarting MCU...
Processing rm495__07.95.mcusw (APE)...
Processing rm495__07.95.ppm_el (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
rm495__07.95.ppm_el, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x01520000-0x01DBFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 24.828s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 21.266s
Flashing Speed: 2331,28 kBit/S
Restarting MCU...
Processing rm495__07.95.ppm_el (APE)...
Processing rm495__07.95.image_el_red (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		192002117FD34950B8A59709FED7C8CD1762B1CE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
rm495__07.95.image_el_red, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC240000008A31, Samsung, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2400 (Samsung), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x01DC0000-0x0215FFFF, NOR
EraseArea[0,CMT]: 0x02160000-0x03FBFFFF, NOR
Waiting 320s for erasure finish...
Erase taken 138.469s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 37.406s
Flashing Speed: 2441,68 kBit/S
Restarting MCU...
Processing rm495__07.95.image_el_red (APE)...
All images processed OK! Processing post flash tasks...
Post flash tasks finished!
Flashing successfully finished!
 
УФС чек:
1ST BOOT  : C0,07 [Rm-495] [2.2.0.3]
CMT ASICID: 000000010000022600010006030C192101033000
EM 1 ID   : 00000296
EM 2 ID   : 00000B22
CMT PUBID : 192002117FD34950B8A59709FED7C8CD1762B1CE
CMT MODE  : 00
CMT HASH  : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROMID : 273F6D55DFAAF68F
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv3_2nd.fg, Ver: 9.11.1
CMT FLID0 : 00EC2400-00008A31, Sam K8x1259ETF
CMT FLCNT : 00000000000000000000000000000000000000
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO  : RAP3Gv3_algo.fg, Ver: 9.17.0
CMT KSIG0 : 0C917F11196FDB7378C18EF7260698CA4489DCA0
CMT VPP   : Internal
DUAL LINE : True
CMT ALG Boot OK
PASUBTOC  : PA_SL3  
Rebooting Mobile

Инфо:
MCU SW  : V 07.95 03-02-10 RM-495 (c) Nokia 
PPM SW  : V 07.95 03-02-10 RM-495 (c) Nokia EL
Product : Nokia 5130c-2
Prd.Code: 0572174
Bpr.Code: 0567772
Prod.Sn : 0AD60A3AI
HW Vers : 2003
EM VILMA: 16
EM BETTY: 22
RFIC Ver: 06540601
DSP Vers: ICPR72_10w01
LCD Type: SEIKO
CAM Prim: NIMMIIIIRRFF094B2F01_002014
IMEI    : 352700-04-509984-2
SL Serv : SIMLOCK SERVER
SL Conf : 244-07-00000000000
SL Prof : 0000000000000000
SL Count: 00 00 
BLK1= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK2= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK3= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK4= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK5= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK6= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
BLK7= L1: OPEN L2: OPEN L3: OPEN L4: OPEN L5: OPEN 
Provider: Nokia Test;Finland

Прошивка:
1ST BOOT  : C0,07 [Rm-495] [2.2.0.3]
CMT ASICID: 000000010000022600010006030C192101033000
EM 1 ID   : 00000296
EM 2 ID   : 00000B22
CMT PUBID : 192002117FD34950B8A59709FED7C8CD1762B1CE
CMT MODE  : 00
CMT HASH  : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROMID : 273F6D55DFAAF68F
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv3_2nd.fg, Ver: 9.11.1
CMT FLID0 : 00EC2400-00008A31, Sam K8x1259ETF
CMT FLCNT : 00000000000000000000000000000000000000
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO  : RAP3Gv3_algo.fg, Ver: 9.17.0
CMT KSIG0 : 0C917F11196FDB7378C18EF7260698CA4489DCA0
CMT VPP   : Internal
DUAL LINE : True
CMT ALG Boot OK
IMAGE : rm495__07.95.mcusw
CMT NOR Erase Area: 0x00000000-000006BF
CMT NOR Erase Area: 0x000006C0-0001FFFF
CMT NOR Erase Area: 0x00040000-000BFFFF
CMT NOR Erase Area: 0x000C0000-0013FFFF
CMT NOR Erase Area: 0x00140000-0137FFFF
CMT NOR Erase Area: 0x01380000-0151FFFF
CMT FLASH ERASE OK, Time: 01:13
Written: 8 Certificate(s)
CMT FLASH WRITE OK, Time: 01:48
Chip SECTOR_SIZE: 128k
Warning, Must be Used 128Kb Sector_Size CNT File
CONVERSION: Already 128K Paged Source
IMAGE : rm495__07.95.image_el_blu
CMT NOR Erase Area: 0x01DC0000-0215FFFF
CMT NOR Erase Area: 0x02160000-03FBFFFF
CNT FLASH ERASE OK, Time: 01:25
CNT FLASH WRITE OK, Time: 01:06
IMAGE : rm495__07.95.ppm_el
CMT NOR Erase Area: 0x01520000-01DBFFFF
PPM FLASH ERASE OK, Time: 00:25
PPM FLASH WRITE OK, Time: 00:35
Flashing Completed, Rebooting Mobile
Set UI Defaults ...
UI Defaults Failed

Сбросы проходят иногда через три четыре чека.Что делать товарищи дальше подскажите?!