Nokia 2700c-2 не включается

[assror]

Принесли та не включается со слов клиента вечером откульчил и утром включил не вклюается хотел перепрошить но програматра ругаются не хотят прошивать
чек уфса

1ST BOOT  : C0,07 [Rm-561] [2.2.0.0]
CMT ASICID: 000000010000022600010006030C192101033000
EM 1 ID   : 00000296
EM 2 ID   : 00000B22
CMT PUBID : 14B00210C6214E5042B78409DA855DAFDF04E1DE
CMT MODE  : 00
CMT HASH  : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROMID : 273F6D55DFAAF68F
CMT 1ST Boot OK
CMT 2ND Bt: RAP3Gv3_2nd.fg, Ver: 9.11.1
CMT MCID0 : FFFF0000-00000000
CMT 2ND Boot OK
CMT ALGO  : RAP3Gv3_algo.fg, Ver: 9.17.0
CMT VPP   : Internal
DUAL LINE : True
CMT ALG Boot OK
PASUBTOC not Exists
Rebooting Mobile

чек цыклона

Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006030C192101033000
CMT_EM_ASIC_ID:		00000296
CMT_EM_ASIC_ID:		00000B22
CMT_PUBLIC_ID:		14B00210C6214E5042B78409DA855DAFDF04E1DE
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC:	273F6D55
CMT_SECURE_ROM_CRC:	DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
Prepare phone failed with message -> Not found required CMT Algorithm
Failed to Check BB5 Flashing Bus  -> Failed to Boot / Prepare Phone

лог прошивки BEST

card found: S/N 2AD4:0118
registered to: asrar

Connect phone on selected interface...

Core version : 1.23 , Rev : 4.8

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm561__09.97.mcusw
PPM : rm561__09.97.ppm_ej
CNT : rm561__09.97.image_ej_blac
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Getting product info...
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response.
[BB5 FLASH]: Bootrom Ok!
ASIC ID:       000000010000022600010006030C192101033000
CPU ID :       RAP3Gv3 , Features : No any extended features
RAP_PUB:   14B00210C6214E5042B78409DA855DAFDF04E1DE
CMT_ROOT:  9DDBFCFE6E73CED7D8C6268C8EB85723
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing UPDAPP...
Processing PASUBTOC...
TIME : Boot time : 00:00:01
->  Error while flashing... :(

Phone disconected!

Connect phone on selected interface...

немогу понять дело в чём тело не водолаз и не ударник