[JayDi]

Сообщение от jblack

MI Redmi Note 4 [mido]

Operation : Identify [ v1.14 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ...
Handshake passed!
BB_IDC_CPU : SnapDragon 625 [MSM8953]
ID_BLOCK_S : 7A71CD6D
ID_BLOCK_I : 000460E1
ID_BLOCK_L : E1AE3D19A3A21649481CAC9B0FFF1F30
ID_BLOCK_L : 3BC5BF16D9F092483796333641B56124
Use CM2 Internal Loader
Loader Sent! Initializing ...
Running FireHose on BBID : MSM8953 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ]
ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200
Storage : MFR : 0x15 , VENDOR : SAMSUNG , NAME : RX1BMB
Boot Ok!


Brand : xiaomi
ProdName : mido
ProdModel : Redmi Note 4
Device : mido
AndroidVer: 7.0
Manufact. : Xiaomi
SysPatch : NRD90M
QLMxCPU : MSM8953

Done!
Elapsed: 00:00:08

Reconnect Power/Cable!

MIAccount reset

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ...
Handshake passed!
BB_IDC_CPU : SnapDragon 625 [MSM8953]
ID_BLOCK_S : 7A71CD6D
ID_BLOCK_I : 000460E1
ID_BLOCK_L : E1AE3D19A3A21649481CAC9B0FFF1F30
ID_BLOCK_L : 3BC5BF16D9F092483796333641B56124
Use CM2 Internal Loader
Loader Sent! Initializing ...
Running FireHose on BBID : MSM8953 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x0000000747C00000 [ eMMC 32 GiB ]
ExtInfo : 0x0001C000/00100000/00001000/00001000/00000200
Storage : MFR : 0x15 , VENDOR : SAMSUNG , NAME : RX1BMB
Boot Ok!


MIAccount reset passed!

Normal reset :
> Select "FORCED FIX" or "REPAIR" in FMT settings, press "Format FS / Reset Settings"
> PowerOn device and use. IF Device stuck on black screen with cable - use another FMT
> Not all devices supported yet! (tested on Hydrogen,Land,Redmi2)

Done!
Elapsed: 00:00:14

Reconnect Power/Cable!

После этого застрял в EDL mode, сдергивание батареи зажатие кнопок не помогает.

Прошить CM2 и QFIL тоже не могут.

Operation : Flash [ v1.14 ]

ForceFlashing : Disabled

Verify FW package ...
Verification passed!

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone...
Device Found!
Initialize ...

Error : Fail to init protocol!
Check cable, connection and drivers!

Reconnect Power/Cable!

Как вернуть к жизни.

Сдернуть питание. Либо - обе кнопки громкости и включение удерживать 30 секунд. Проще сразу кабель в комп, как только винда даст звук переподключения - шить.

Сообщение от Mumang

При обрыве слива через Emmc Read/Write разделов и краше потом не запускается софт, лечение банально грохнуть Operation.log в папке программы.

Проверю.