[Fluderator]

Вот весь лог проделанный Циклоном в порядке его последовательности

Фулл Еразе
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
Erasing flash chip...
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x07FFFFFF, ONENAND
Waiting 640s for erasure finish...
Erase taken 1.437s
Restarting MCU...
BB5 Full Erase Finished!

Прошивка
Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm243_07.10_prd_core.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
rm243_07.10_prd_core.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0xFFFFFFFF00000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
Warning: PAPUBKEYS Hash Missing!
Flashbus Write baud set to 5.0Mbits
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00040000-0x00082FFF, ONENAND
EraseArea[0,CMT]: 0x00083400-0x0087FFFF, ONENAND
EraseArea[0,CMT]: 0x00B80000-0x04DFFFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 0.953s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT PASUBTOC Certificate...
WARNING: CMT PAPUBKEYS Hash is Empty, writing first found PAPUBKEYS
Writing CMT PAPUBKEYS Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS*CORE Certificate...
Writing CMT SOS+ROFS Certificate...
Programming Status OK!
All blocks written OK! Time taken 48.828s
Flashing Speed: 7496,31 kBit/S
Restarting MCU...
Processing rm243_07.10_prd_core.fpsx (APE)...
Processing rm243_07.10_prd_vB05_03_russian.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
rm243_07.10_prd_vB05_03_russian.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x03300000-0x04DFFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.329s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFX Certificate...
Programming Status OK!
All blocks written OK! Time taken 27.781s
Flashing Speed: 7175,30 kBit/S
Restarting MCU...
Processing rm243_07.10_prd_vB05_03_russian.fpsx (APE)...
Processing rm243_ENO_A_2009wk15v0.100.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
rm243_ENO_A_2009wk15v0.100.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x00880000-0x00B7FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.47s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS*ENO Certificate...
Programming Status OK!
All blocks written OK! Time taken 1.687s
Flashing Speed: 6991,72 kBit/S
Restarting MCU...
Processing rm243_ENO_A_2009wk15v0.100.fpsx (APE)...
Processing rm243_07.10_prd_UDA_Pink.fpsx (CMT)...
Booting CMT...
CMT_SYSTEM_ASIC_ID:	000000010000022600010006400C192101031103
CMT_EM_ASIC_ID:		00000295
CMT_EM_ASIC_ID:		00000B21
CMT_PUBLIC_ID:		1730001978B901584A11D929C0CF1AE792AD304A
CMT_ASIC_MODE_ID:	00
CMT_ROOT_KEY_HASH:	CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT_BOOT_ROM_CRC:	4B9B7510
CMT_SECURE_ROM_CRC:	3E691FF8
CMT Ready!
rm243_07.10_prd_UDA_Pink.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5
Searching for BootCode: DualLine 32Bit
RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.12.8.0, Algo: BB5
Flashbus Write baud set to 650Kbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC003000000221, Samsung, ONENAND
Requested Algorithm: XSR 1.5 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.12.8.0, Algo: XSR 1.5
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0FE1BA92D924A658E4800780FA6F4868100AC947
Flashbus Write baud set to 5.0Mbits
Started group flash erase
EraseArea[0,CMT]: 0x04E00000-0x07B3FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.531s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 0.953s
Flashing Speed: 956,90 kBit/S
Restarting MCU...
Processing rm243_07.10_prd_UDA_Pink.fpsx (APE)...
All images processed OK! Processing post flash tasks...
Post flash tasks finished!
Flashing successfully finished!

В одно сообщение не помещается,продолжение лога ниже...